You are here: Home » Products » Brushless Motors » NEMA32-80×80MM

Product Category

NEMA32-80×80MM

80mm Brushless Motor | NEMA32 Brushless Motor


80mm Brushless Motor is a common brushless motor with many advantages. Firstly, it adopts brushless technology, which has higher efficiency and longer service life than the traditional brushed motor.Secondly, this model of motor is small and light, and can play an excellent performance in various application scenarios.

 80mm Brushless Motor is widely used in industrial fields.For example, in the automation production line, it can drive various equipment and mechanical arms for accurate control;in the aerospace field, it can be used as an important part of the aircraft propulsion system;and in the smart home products, it can provide powerful and quiet operation of the power support.

 In addition, 80mm Brushless Motor is also widely used in model making, medical equipment, automobile industry and other fields.Its high efficiency and low noise characteristics make it one of the indispensable key components in these fields.

 In summary, 80mm Brushless Motor / NEMA32 Brushless Motor is widely recognized for its high efficiency, durability, lightweight and other characteristics, and has shown excellent performance in many fields.


What is an 80mm brushless motor?

An 80mm brushless motor refers to a type of electric motor that does not have brushes for commutation.  It typically has a diameter of 80mm, which determines its size and power output.


How does an 80mm brushless motor work?

An 80mm brushless motor operates using electronic commutation instead of mechanical brushes.  It consists of a rotor with permanent magnets and a stator with windings.  The electronic controller sends signals to the windings, creating magnetic fields that interact with the magnets on the rotor, causing it to rotate.


What are the advantages of using an 80mm brushless motor?

Some advantages include higher efficiency, longer lifespan due to no brushes wearing out, smoother operation resulting in less noise and vibration, better control over speed and torque, and improved power-to-weight ratio.


Can I use an 80mm brushless motor for my RC car/boat/plane?

Yes, depending on your specific requirements such as voltage range and power output needed for your application, you can choose an appropriate 80mm brushless motor designed for RC vehicles or aircraft.


How do I select the right ESC (Electronic Speed Controller) for my 80mm brushless motor?

To select the correct ESC for your motor, consider factors such as voltage compatibility (matching or exceeding the battery's voltage), current rating (ampere capacity), programming options if required (such as brake settings), and physical size constraints.


Are there any maintenance requirements for an 80mm brushless motor?

Generally speaking, these motors require minimal maintenance compared to brushed motors since they lack brushes that wear out over time.  However, regular cleaning from dust or debris accumulation is recommended along with occasional lubrication if specified by the manufacturer.


Can I run my 12V-rated 80mm brushless motor at higher voltages like 24V or more?

It is crucial to operate within the manufacturer's specified voltage range mentioned in their documentation or product specifications sheet provided with your particular model of an 80 mm brushless motor;  exceeding this limit may damage or even destroy it.


Is it possible to reverse the rotation direction of my 80 mm brushless DC Motor?

Yes!  By swapping any two wires connected between your ESC/controller and your Brushess DC Motor will change its rotation direction effectively reversing it


What are some common applications where we find usage of these motors?

These motors find applications across various industries including robotics systems ,drones ,electric vehicles , industrial automation equipment etc


How do i calculate Power Rating / Torque requirement ?

Power = Voltage * Current ;  Torque = Force * Distance .  You need information about either one parameter among Power/Torque alongwith other parameters like RPM/Voltage/Current etc inorder calculate remaining ones .


Can i use PWM signal directly from microcontroller pins ?

No !  Most microcontrollers cannot provide enough current through their GPIO pins so you would need additional driver circuitry like MOSFETs/H-Bridge ICs etc inorder to drive these high-powered Motors


What kindof cooling mechanism should be used while operating at high loads?

For continuous operations under heavy load conditions, active cooling mechanisms like fans/heatsinks/water-cooling setups might be necessary in order keep temperatures under check & prevent overheating/damage


Are there any safety precautions while handling these Motors?

Always ensure proper insulation & grounding when working around electrical components.  Avoid touching live terminals during operation .  Follow all safety guidelines mentioned by manufacturers.


What are some key differences between Brushed vs Brushless Motors?

Brushed Motors : Simpler construction , lower cost but limited life span due carbon-brushes wearing off

Brushess Motors : Higher Efficiency,longer life span but complex electronics involved making them expensive than brushed counterparts.


What is a NEMA32 brushless motor?

A NEMA32 brushless motor refers to a type of electric motor that operates without brushes and uses electronic commutation instead.  It belongs to the National Electrical Manufacturers Association (NEMA) standard size 32 category, which specifies its physical dimensions.


How does a NEMA32 brushless motor work?

A NEMA32 brushless motor works by using magnets on the rotor and electromagnets on the stator to generate rotational motion.  The electronic controller sends signals to energize specific coils in sequence, creating a rotating magnetic field that propels the rotor.


What are the advantages of using a NEMA32 brushless motor?

Some advantages of using a NEMA32 brushless motor include higher efficiency, longer lifespan due to absence of brushes, reduced maintenance requirements, smoother operation with less noise and vibration, precise speed control capabilities, and improved torque-to-weight ratio.


Where can I use a NEMA32 brushless motor?

NEMA32 brushless motors find applications in various industries such as robotics, CNC machines, 3D printers, automation systems, medical equipment, aerospace technology (where applicable regulations permit), industrial machinery (excluding sensitive sectors), and other areas requiring high-performance motion control.


Are there any limitations or considerations when using a NEMA32 brushless motor?

While generally reliable and efficient for many applications, it is important to consider factors such as power supply compatibility (voltage/current ratings), temperature limits for proper cooling/ventilation arrangements if necessary;  mechanical mounting requirements;  appropriate wiring connections;  suitable protection against dust/water ingress based on environmental conditions;  adherence to safety guidelines during installation/use/maintenance processes.


Can I directly replace my existing brushed DC or stepper motors with a NEMA32 brushless motor?

In some cases where electrical/mechanical specifications align properly with your application's requirements (e.g., voltage range compatibility), it may be possible to replace brushed DC or stepper motors with equivalent-rated NMEA 34 models after considering additional factors like controller compatibility and system integration aspects.


How do I select the right driver/controller for my NMEA 34 brushless motor?

To select an appropriate driver/controller for your specific application needs:

  • Determine required voltage/current ratings.

  • Consider desired features/functions like speed/torque control options.

  • Ensure compatibility between driver/controller interface protocols/formats used by your system.

  • Consult manufacturer datasheets/manuals or seek expert advice if needed.


Can you recommend any reputable manufacturers/suppliers of quality NEMEA 34 brushless motors?

Apologies but we cannot provide specific recommendations regarding manufacturers/suppliers due to our neutral stance in this regard.


How do I maintain/clean my NEMEA 34 brushlesssmotor?

Maintenance procedures may vary depending on individual product specifications provided by manufacturers/suppliers through their user manuals/datasheets/support channels/etc..  It is recommended to follow those guidelines strictly while ensuring safe practices during cleaning/lubrication/checking connections/replacing worn-out parts(if applicable).


Contact Holry Support Team Now
Changzhou Holry Electric Technology Co., Ltd. specializes in the development and production of stepper motors, hybrid stepper motor, CNC machine motor, screw motor, spindle motors, air cooled spindle, brushless motors, stepper motor screwstepper motor gearbox, servo motors and drive systems.

QUICK LINKS

CONTACT US
  Tel : +86 0519 83660635
  Phone : +86- 13646117381
 E-mail : holry@holrymotor.com
© COPYRIGHT 2023 CHANGZHOU HOLRY ELECTRIC TECHNOLOGY CO., LTD. ALL RIGHTS RESERVED.